TB 1--1520--237--20--236
force required to close the handle shall be 25 pounds minumim, with two threads extending beyond the nut.
Replace pin if criteria is not met."
l. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.1.b.(2), shall be changed to read: "Keeping
the spring force perpendicular to the long, riveted section of the handle, the force to close the handle shall
be 25 pounds minumim."
m. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.1.b.(3) (a), shall be changed to read: "If force
required to close handle is not at least 25 pounds, perform the following: Tighten nut. Rotate nut 1/6 (one
sixth) turn and recheck closing force. Repeat until minumim of 25 pounds closing force is obtained."
n. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.1.b.(3) (b), shall be changed to delete: "
Repeat tension check."
o. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.1b.(4) (b) , shall be changed to read: " Re-
peat tension check. Keeping the spring force perpendicular to the long, riveted section of the handle, the
force required to close the handle shall be 25 pounds minumim, with two threads extending beyond the nut.
Replace pin if criteria is not met."
p. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.4.l (2) , shall be changed to read: " Keeping
the spring force perpendicular to the long, riveted section of the handle, the force required to close the handle
shall be 25 pounds minumim."
q. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.4.l (3) (a), shall be changed to read: "If force
required to close handle is not at least 25 pounds, perform the following: Tighten nut. Rotate nut 1/6 (one
sixth) turn and recheck closing force. Repeat until minumim of 25 pounds closing force is obtained."
r. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.4.l (3) (b), shall be changed to delete: " Re-
peat tension check."
s. Technical Manual 1-1520-250-23-3, paragraph 5.17.1.4.l (4) (b), shall be changed to read: " Repeat
tension check. Keeping the spring force perpendicular to the long, riveted section of the handle, the force
required to close the handle shall be 25 pounds minumim, with two threads extending beyond the nut. Re-
place pin if criteria is not met."
10. Supply/Parts and Disposition.
NOTE
HQDA-ODCSOPS will prioritize units and repair parts distribution.
a.
Parts required. Items cited in paragraph 12.c. may be required to replace defective items.
b. Requisitioning instructions. Requisition replacement parts using normal supply procedures. All
requisitions shall use project code (CC 57-59) "X1D" (X-ray-One-Delta).
NOTE
Project code "X1D" is required to track and establish a data base of stock fund expenditures in-
curred by the field as a result of message actions.
c.
Bulk and Consumable Materials:
NOMENCLATURE
PART NUMBER
NSN
Dry Cleaning Solvent
P-D-680, Type 2
Machinery Towel
DDD-T-541
d. Disposition. Complete DD Form 1577/DD Form 1577-1. Hold any discrepant part/component
pending disposition instructions from the Tecnical Point of Contact in paragraph 16.a..
e. Disposition of Hazardous Material. IAW Environmental Protection Agency directives as implement-
ed by your servicing environmental coordinator (AR 200-1).
4