Seciton I : INTRODUCTION

Section I

INTRODUCTION

Code

Explanation

1. Scope

Repair parts which are not procured or stocked. The

This manual lists repair parts and special tools required

requirement of such items will be filled by the use

for the performance of direct support, general support,

of the next higher assembly or component.

and depot maintenance of the snow removal unit.

Repair parts which are not stocked. The indicated

2. General

maintenance category requiring such repair parts

This Repair Parts and Special Tools List is divided into

will

attempt

obtain

same

through

the following sections:

cannibalization. Where such repair parts are not

obtainable through cannibalization, requirements

a. Repair Parts - Sections II. A list of repair parts

will be requisitioned, with accompanying

authorized for the performance of maintenance at the

justification, through normal supply channels.

direct support, general support, and depot level in figure

Major assemblies that are procured with PEMA funds

and item number sequence.

for initial issue only as exchange assemblies at

b. Special Tools, Test and Support Equipment

DSU and GSU level. These assemblies will not be

Section III. A list of special tools, test and support

stocked above DSU and GSU level or re turned to

equipment authorized for the performance of

depot supply levels.

maintenance at the direct support, general support, and

(2) Maintenance code, indicates the lowest

depot level.

category of maintenance authorized to install the listed

c. Index - Federal Stock Number acid Reference

item. The maintenance level code is:

Number - Sections IV. A list of Federal stock numbers

Code

Explanation

O ........................Organizational maintenance

in ascending numerical sequence followed by a list of

F.........................Direct support maintenance

reference numbers in ascending alpha-numeric

H ........................General support maintenance

sequence, cross-referenced to the illustration figure

D ........................Depot maintenance

number and item number.

(3) Recoverability code, indicates whether

Note

unserviceable items should be returned for recovery or

Items not illustrated are cross-

salvage.

Items not coded are expendable.

referenced to page number.

Recoverability codes are:

3. Explanation of Columns

Code

Explanation

The following provides an explanation of columns in the

Applied to repair parts and assemblies which are

tabular lists in sections II and III.

economically repairable at DSU and GSU activities

a. Source, Maintenance, and Recoverability Codes

and furnished by supply on an all exchange basis.

(SMR).

Repair parts and assemblies which are economically

repairable at DSU and GSU activities and which

(1) Source code, indicates the selection

normally furnished by supply on an exchange

status and source for the listed item. Source codes are:

basis. When, items are determined by a GSU to

Code

Explanation

be uneconomically repairable they will be

Repair parts which are stocked in or supplied from

evacuated to a depot for evaluation and analysis

the GSA/DSA, or Army supply system and

before final disposition.

authorized for use at indicated maintenance

High dollar value recoverable repair parts which are

categories.

subject to special handling and are issued on an

Repair parts which are not procured or stocked, but

exchange basis. Such repair parts are normally

are to be manufactured in indicated maintenance

repaired or overhauled at depot maintenance

levels.

activities.

Assemblies which are not procured or stocked as

Repair parts specifically selected for salvage by

such, but are made up of two or more units. Such

reclamation units because of precious metal

component units carry individual stock numbers

content, critical materials, or high dollar value

and descriptions are procured and stocked

reusable casings or castings.

separately and can be assembled to form the

b. Federal Stock Number. This column indicates

required assembly at indicated maintenance

the Federal stock number assigned to the item and will

categories.

be used for requisitioning purposes.

Parts and assemblies which are not procured or

stocked and the mortality of which normally is

c. Description. This column indicates the Federal

below that of the applicable end item or

item name and any additional description of the item

component. The failure of such part or assembly

required. Assembly components and sub-assemblies

should result in retirement of the end item from the

are indented under major assemblies. The abbreviation

supply system.

"w/e" when used as a part of the nomenclature