2-1 ------Scaling networks, schematic diagram --------------------------------------------------------------------------------------------- 2-7

2-2 ------Image motion compensation (imc), block diagram----------------------------------------------------------------------------- 2-9

2-3 ------Image motion compensation (imc), schematic diagram ---------------------------------------------------------------------- 2-9

2-4 ------Scan drive system, block diagram ------------------------------------------------------------------------------------------------2-12

2-5 ------Scan drive system, waveforms-----------------------------------------------------------------------------------------------------2-13

2-6 ------Drive mechanism, schematic diagram -------------------------------------------------------------------------------------------2-14

2-7 ------Intervalometer pulse circuit, schematic diagram ------------------------------------------------------------------------------2-15

2-8 ------Conversion of V/H signal to Intervalometer pulse -----------------------------------------------------------------------------2-16

2-9 ------Fail safe and frames remaining circuits, schematic diagram ---------------------------------------------------------------2-16

2-10 ----Annotation pulse circuit, schematic diagram------------------------------------------------------------------------------------2-17

2-11 ----Auxiliary data annotation system (adas), block diagram---------------------------------------------------------------------2-17

2-12 ----Interface board assembly, schematic diagram ---------------------------------------------------------------------------------2-19

2-13 ----Auxiliary data annotation system (adas), functional diagram---------------------------------------------------------------2-20

2-14 ----Film transport, timing diagram -----------------------------------------------------------------------------------------------------2-21

3-1 ------Power supply board assembly, test setup ---------------------------------------------------------------------------------------- 3-3

3-2 ------Scan heat sink assembly, test setup ----------------------------------------------------------------------------------------------- 3-4

3-3 ------Aec assembly, exploded view ------------------------------------------------------------------------------------------------------- 3-8

3-4 ------Body, exploded view ------------------------------------------------------------------------------------------------------------------3-16

3-5 ------Installation of AEC assembly -------------------------------------------------------------------------------------------------------3-28

3-6 ------Installation of puck switch -----------------------------------------------------------------------------------------------------------3-22

3-7 ------Motor, gears, and tachometer-generator, exploded view --------------------------------------------------------------------3-30

3-8 ------Camera control, exploded view ----------------------------------------------------------------------------------------------------3-32

3-9 ------Scan heat sink assembly, exploded view----------------------------------------------------------------------------------------3-33

3-10 ----Power supply assembly, exploded view -----------------------------------------------------------------------------------------3-34

3-11 ----Power supply board assembly, installation dimensions ----------------------------------------------------------------------3-35

3-12 ----Interconnecting board assembly, exploded view ------------------------------------------------------------------------------3-36

3-13 ----Control panel, exploded view -------------------------------------------------------------------------------------------------------3-38

3-14 ----Interface board assembly, exploded view ---------------------------------------------------------------------------------------3-40

3-15 ----CAMERA SEL switch S4, terminals and jumper wire connections --------------------------------------------------------3-41

3-16 ----Magazine, exploded view ------------------------------------------------------------------------------------------------------------3-42

3-17 ----Pressure plate assembly, exploded view ----------------------------------------------------------------------------------------3-51

3-18 ----Keeper block assembly, exploded view ------------------------------------------------------------------------------------------3-52

3-19 ----Pressure roller assembly, exploded view ----------------------------------------------------------------------------------------3-53

3-20 ----Tilt set cables ---------------------------------------------------------------------------------------------------------------------------3-54

3-21 ----Aec assembly ---------------------------------------------------------------------------------------------------------------------------3-54

4-1 ------Interface board assembly, test setup --------------------------------------------------------------------------------------------- 4-6

4-2 ------Aec board assembly, test setup ----------------------------------------------------------------------------------------------------- 4-7

4-3 ------Control board assembly, test setup ------------------------------------------------------------------------------------------------ 4-8

4-4 ------Scan board assembly, test setup --------------------------------------------------------------------------------------------------4-9

4-5 ------Tachometer-generator calibration, test setup-----------------------------------------------------------------------------------4-10

4-6 ------Extra picture circuit waveform ------------------------------------------------------------------------------------------------------4-10

4-7 ------Frames remaining and cycle indicator circuit waveform ---------------------------------------------------------------------4-11

4-9 ------Intervalometer waveform at pin 2U -----------------------------------------------------------------------------------------------4-14

4-10 ----Intervalometer waveform at pin 2X -----------------------------------------------------------------------------------------------4-14

4-11 ----Pulse width balance waveform -----------------------------------------------------------------------------------------------------4-14

4-12 ----Location of camera body phasing hole -------------------------------------------------------------------------------------------4-18

4-13 ----Aec alinement and calibration tests -----------------------------------------------------------------------------------------------4-19

4-14 ----Scan motor, exploded view ---------------------------------------------------------------------------------------------------------4-21

5-1 ------Alinement of prism and helical gear and sprocket assembly ----------------------------------------------------------------5-2

5-2 ------Straight shaft, fabrication dimensions --------------------------------------------------------------------------------------------- 5-2

5-3 ------Alinement of gears and cam on shaft---------------------------------------------------------------------------------------------- 5-2

5-4 ------Cover, fabrication dimensions ------------------------------------------------------------------------------------------------------- 5-3

5-5 ------Mending plate, fabrication dimensions -------------------------------------------------------------------------------------------- 5-4

5-6 ------Light shield, fabrication dimensions ------------------------------------------------------------------------------------------------ 5-4

6-1 ------V/H control panel, schematic diagram--------------------------------------------------------------------------------------------- 6-2