Click here to make tpub.com your Home Page

Page Title: Table 2-4. Oscilloscope Check Procedures - continued
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home
   
Information Categories
.... Administration
 Advancement
 Aerographer
 Automotive
 Aviation
 Construction
 Diving
 Draftsman
 Engineering
 Electronics
 Food and Cooking
 Logistics
 Math
 Medical
 Music
 Nuclear Fundamentals
 Photography
 Religion
   
   

 
Back
Table 2-4. Oscilloscope Check Procedures		Up
TM-9-6625-1753-14		Next
Table 2-4. Oscilloscope Check Procedures - continued

TM 9-6625-1753-14
C3
Table 2-4. Oscilloscope Check Procedures-Continued
Table 2-4. Oscilloscope Check Procedures-Continued
Step
Operation
Normal Indication
Corrective procedure
Step
Operation
Normal Indication
Corrective procedure
Refer to the dual trace plug-in func-
5.  Check Triggered Delayed Sweep.
tional schematic (Fig. 4-4 or 4-4.1).
a. Adjust the DELAY VERNIER control (37) until the strobe (brightened portion) covers the leading edge of the
d.
Set the channel B NORM-INVERT switch (49 or 71) to INVERT (or INVERT AC).
waveform.
b. Set the DISPLAY LOGIC switch to TRIG-DLY'D.
A 4-division square wave is present.
Refer to the dual trace plug-i n func-
The portion of the waveform previously covered by the strobe is not on the screen,
tional schematic (Fig. 4-4 or 4-4.1).
horizontally expanded or magnified 5 times (10 divisions).
e.
Set the MODE switch to A (or CH1), and the NORM-INVERT switch to NORM (or NORM AC).
Refer to the delaying sweep plug-in
functional schematic (Fig. 4-5 or 3-18).
Check delayed sweep circuit of the de-
3.
Check the X10 Probes.
a.  Connect one X10 probe to the channel A 1 MEG connector (54) and the other X10 probe to the channel B 1 MEG
laying sweep plug-in.
connector (47)(or CH1 1 MEG 14PF and CH2 1 MEG 14PF, 74 and 69, respectively).
Note.  It may be necessary to slightly adjust the DELAY VERNIER control to see the leading edge of the
b. Set the channel A and channel B VOLTS/DIV switches to .02 (or 0.2 and PULL X10).
waveform.
c.  Connect the channel A probe tip to the CAL IV connector (4 1).
A 5-division peak-to-peak square wave is present.
6.
Check Delay Vernier Control.
Center the waveform on the CRT with
a.  Set the DELAYED SWEEP-PULL TO UNLOCK switch (26) to 0.2 mSEC (for 400-Hz source); 1 mSEC for 60-Hz
the channel A POSITION control (5 or
source.
56) if necessary.
b. Set the DELAY VERNIER control to 0 (on both the window and knob skirt).
Rotate the body of the probe if the
c.  Set the DISPLAY LOGIC switch to TRIG-STROBE.
square wave is distorted (overshoot or
d.  Set the DELAY VERNIER control to 4 (window)(on the skirt).
undershoot).
The 2-division waveform portion between the 4th and 6th divisions is brighter than the
Perform the probe set-up procedure
remainder of the presentation.
(par. 2-8a).
Refer to the delaying sweep plug-in
Refer to par. 2-7.
functional schematic (Fig. 4-5 or 3-16).
d.  Set the MODE switch to B (or CH2).
Check delay pick-off circuit of the de-
e.  Repeat step c for the channel B probe.
laying sweep plug-in.
Center the waveform on the CRT with
7.
Check Armed-Strobe Sweep.
the Channel B POSITION control (44
a.  Set the DELAYED SWEEP-PULL TO UNLOCK switch to 5 mSEC.
or 65) if necessary.
b. Set the DISPLAY LOGIC switch to ARM-STROBE.
f.  Set the MODE switch to A (or CH1).
The strobe (brightened segment) appears on the leading edge of the waveform. The
g.  Set the channel A and channel B VOLTS/DIV switches to CAL.
SWP READY indicator lamp (35) flickers.
Refer to the delaying sweep plug-in
functional schematic (Fig. 4-5 or 3-18).
4.
Check Triggered-Strobe Sweep.
Check delayed sweep circuit of the de-
a.
Pull the DELAYED SWEEP-PULL TO UNLOCK switch (26), and rotate it until the white scribe mark is alined with
laying sweep plug-in.
the .5 mSEC position. (The cutout of the TIME/DIV switch plastic skirt should still be at the initial setting.)
8.
Check Armed-Delayed Sweep.
b. Set the DISPLAY LOGIC switch to TRIG-STROBE.
a.  Set the DISPLAY LOGIC switch to ARM-DLY'D.
A small portion of the square-wave signal is brighter than the rest of the waveform.
The strobe portion (leading edge of the waveform) is now present, horizontally
Adjust the DELAY VERNIER control
expanded or magnified 5 times. The SWP READY indicator lamp continues to flicker.
(37).
Refer to the delaying sweep plug-in
Refer to the delaying sweep plug-in
functional schematic (Fig. 4-5 or 3-18).
functional schematic (Fig. 4-5 or 3-16).
Check delayed sweep circuit of the de-
Check delayed sweep circuit of the de-
laying sweep plug-in.
laying sweep plug-in.
b. Set the channel A VOLTS/DIV switch to .02 (or .2 and PULL X10).
c.  Set both SOURCE switches (21 and 29) to INT.
d.  Rotate the LEVEL control (36) to eithe r extreme.
2-10

Privacy Statement - Press Release - Copyright Information. - Contact Us