|
| |
- TECHNICAL MANUAL OPERATOR,
ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
MANUAL
- WARNING
- DISTRIBUTION
- TECHNICAL MANUAL OPERATOR,
ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
MANUAL
- WARNING
- DISTRIBUTION
- WARNING
- DISTRIBUTION
- WARNING
- Overflow Reservoir Level
Switch (Model VBM-250A)
- DISTRIBUTION
- WARNING
- WARNING
- Figure 1-1.1 Heater assembly
(Model VBM-250A)
- Figure 1-3.1 Fuel flow
diagram (Model VBM-250A)
- Figure 1-4. Safety and engine
controls wiring diagram (Model VBM-250A)
- Figure 2-1. Controls and
instruments. (2 of 2)
- Attaching 12-Inch Canvas
Ducts (Model VBM-250)
- ENGINE STOPS - BURNER LIT
(MODEL VBM-250A)
- ENGINE STOPS -BURNER LIT
(MODEL VBM-250A) (CON'T)
- Figure 4.6.1 Heater duct
storage basket, removal and installation (Model VBM-250A).
- Storage Basket Cover (Model
VBM- 250A)
- Figure 4-7. 1 Heater cabinet,
removal and installation (Model VBM-250A).
- Figure 4-10. Control damper,
removal and installation.
- igure 4-11.1 Electrical
schematic (Model VBM-250A).
- Figure 4-11.2 Overflow
reservoir system {Model VBM-250A)
- Figure 4-14. Fuel tank
fittings, removal and installation
- Distribution
- Figure 5-3.1. Burner assembly
(Model VBM-250A).
- Distribution
- Warning Page
- Figure 1-1. Heater assembly.
- Figure 1-3. Fuel flow diagram
- Figure 2-1. Controls and
instruments.
- Figure 2-3. Starting.
- Figure 2-4. Stopping.
- Figure 4-1. Engine, removal
and installation.
- Figure 4-2. Fuel lines,
removal and installation.
- Figure 4-7. Heater cabinet,
removal and installation
- Figure 5-1. Overheat control,
removal and installation
- Appendix B MAINTENANCE
ALLOCATION CHART
- Section II. MAINTENANCE
ALLOCATION CHART
- Section II. MAINTENANCE
ALLOCATION CHART -- CONTINUED
- Section II. MAINTENANCE
ALLOCATION CHART -- CONTINUED
- OPERATOR, ORGANIZATIONAL,
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL
- LIST OF ILLUSTRATIONS
- CHAPTER 1 INTRODUCTION
- Figure 1-1. Heater Assembly
- Section II. DESCRIPTION AND
DATA
- Figure 1-3. Fuel flow diagram
- Tabulated Data
- CHAPTER 2 OPERATING
INSTRUCTIONS
- Figure 2-1. Controls and
instruments.
- Figure 2-2. Controls and
instruments, continued
- Attaching 6-Inch Canvas Ducts
- Figure 2-3. Starting
- Figure 2-4. Stopping.
- Section II. OPERATION UNDER
UNUSUAL CONDITIONS
- Figure 2-5. Winterization
torch
- CHAPTER 3 OPERATOR/CREW
MAINTENANCE INSTRUCTIONS
- Section III. TROUBLESHOOTING
- Section IV. MAINTENANCE
PROCEDURES
- CHAPTER 4 ORGANIZATIONAL
MAINTENANCE INSTRUCTIONS
- Preventive Maintenance
Services
- Table 4.2 Troubleshooting
- Section IX. MAINTENANCE,
ENGINE
- Figure 4-2. Fuel lines,
removal and installation
- Exhaust Pipe
- Engine Base
- Figure 4-5. Engine support
bracket, removal and installation.
- Section X. MAINTENANCE OF THE
HEATER ASSEMBLY
- Spring Lock Snap
- Figure 4-7. Heater cabinet,
removal and installation.
- Figure 4-8. Burner access
door, removal and installation.
- Handle
- Value, Temperature Control
- Figure 4-12. Inner air ducts
and damper, removal and installation.
- Figure 4-13. Fan, blower
wheel and guard, removal and installation.
- Figure 4-14. Fuel gage,
removal and installation
- CHAPTER 5 DIRECT SUPPORT AND
GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- REMOVAL AND INSTALLATION OF
MAJOR COMPONENTS AND ASSEMBLY
- Figure 5.2. Burner, removal
and installation
- Figure 5-3. Burner assembly
- Figure 5-4. Combustion
chamber, removal and installation
- Figure 5-5. Fuel tank,
removal and installation.
- Figure 5-6. Axle, removal and
installation.
- Figure 5-7. Rear panel,
removal and installation.
- Figure 5-8. Heater frame
assembly.
- CHAPTER 6 REPAIR OF THE
PORTABLE GASOLINE HEATER
- CHAPTER 7 ADMINISTRATIVE
STORAGE
- APPENDIX A REFERENCES
- APPENDIX B MAINTENANCE
ALLOCATION CHART
- Section II. MAINTENANCE
ALLOCATION CHART
- Section III. SPECIAL TOOL AND
SPECIAL TEST EQUIPMENT REQUIREMENTS
- Section Il. COMPONENTS OF END
ITEM
- APPENDIX C COMPONENTS OF END
ITEM AND BASIC ISSUE ITEMS LISTS
- Section III. BASIC ISSUE
ITEMS
- ALPHABETICAL INDEX
- ALPHABETICAL INDEX cont'd
- Distribution
- THE METRIC SYSTEM AND
EQUIVALENTS
- TM-5-4520-224-14
- RECOMMENDED CHANGES TO
EQUIPMENT TECHNICAL PUBLICATIONS
- Blank Page
|
|