Click here to make tpub.com your Home Page

Page Title: Table 4-1. Troubleshooting (Cont)
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home
   
Information Categories
.... Administration
 Advancement
 Aerographer
 Automotive
 Aviation
 Construction
 Diving
 Draftsman
 Engineering
 Electronics
 Food and Cooking
 Logistics
 Math
 Medical
 Music
 Nuclear Fundamentals
 Photography
 Religion
   
   

 
Back
Table 4-1. Troubleshooting		Up
TM-55-4920-244-14 Tester Exhaust Gas Temperature Model BH112JA-36 Manual		Next
Section Ill. REPAIR PROCEDURES

TM 55-4920-244-14
Table 4-1. Troubleshooting-Continued
Malfunction
Probable cause
Corrective action
8. Heater probes will not heat;
a. Defective voltage regulator.
a. Replace voltage regulator
20 amp fuse not blown.
(para. 4-38).
b. Defective heater probe or
b. Replace heater probe or
heater cable.
heater cable.
a. Defective switch SW-2.
9. No temperature indication
a. Replace switch (para. 4-46).
with switch SW-2 in S-1
b. Defective wiring in ther-
b. Repair or replace wiring
position.
mocouple circuit.
(para,
c. Heater cable connector de-
c. Replace heater cable.
fective.
10. No temperature indication
a. Defective wiring in check
a. Repair or replace wiring
with switch SW-2 in S-2
cable thermocouple circuit,
(para.
position.
b. Defective switch SW-2.
b. Replace switch (para. 4-46).
11. Galvanometers (GALVO-1)
a. Defective switch SW-1.
a. Replace switch.
b. Open potentiometer (oC
cannot be set to zero with
b. Replace potentiometer (para.
potentiometer R-1.
scale).
4-42).
c. Defective potentiometer R-1.
c. Replace potentiometer (para.
4-44).
d. Incorrect EGT indicator cir-
d. See figure 4-15 and test
cuit reference voltage.
following components of
cable and printed circuit
board assembly, part no.
BH1766; T2, CR1, CR2,
CR3, CR4, CR5, CR6,
CR7, CR8, R2, R3, R13,
and R19. Replace defective
components (para. 4-17).
12. Galvanometers (GALVO-1)
a. See figure 4-15 and test
a. Defective reference resistor.
cannot be set to zero by
following components:
adjusting resistance spool
R28, R29, R30, R31, R32,
in aircraft.
and R45. Replace defective
components (para. 4-17).
b. Replace printed circuit board
b. Defective printed circuit
assembly.
board assembly, part no.
BH1760.
c. Replace cable and printed
c. Defective cable and printed
circuit board assembly
circuit board assembly,
(para. 4-39).
part no. BH1766.
d. Replace switch.
d. Defective switch SW-3.
a. Replace meter (para. 4-43).
a. Defective insulation check
13. INSULATION CHECK
meter,
meter will not zero with
b. Replace switch .
b. Defective switch SW-8.
insulation check adapter
c. Replace printed circuit board
c. Defective printed circuit
leads shorted and switch
assembly.
board assembly, part no.
SW-8 in either position.
BH1760.
d. Adjust circuit.
d. Circuit out of adjustment.
e. See figure 4-15 and test R38,
e. Defective adjustment po-
R40, R42, and R44. Replace
tentiometer.
defective components
(para.
4-9
Change 1

Privacy Statement - Press Release - Copyright Information. - Contact Us