Section I. INTRODUCTION

11-6625-2724-20P

SECTION I

INTRODUCTION

Definition

Code

1. S c o p e

PA--Item procured and stocked for anticipated

This manual lists repair parts required for per-

o r known usage.

f o r m a n c e of organizational and depot maintenance

XD--A support item that is not stocked. When

of the ME-202C/U.

required, item will be procured through

normal supply channels.

General

NOTE

This Repair Parts and Special Tools List is divided

Cannibalization or salvage may be used

i n t o the following sections:

as a source of supply for any items

a. Section II. Repair Parts List. A list of repair

source-coded

above,

except

those

coded

parts authorized for use in the performance of

XA, XD, and aircraft support items as

maintenance. The list also includes parts which

r e s t r i c t e d by AR 70042.

must be removed for replacement of the author-

(2) Maintenance code. M a i n t e n a n c e c o d e s a r e

i z e d parts. Parts lists are composed of functional

assigned to indicate the levels of maintenance

g r o u p s in ascending numerical sequence, with the

authorized to USE and REPAIR support items.

parts in each group listed in figure and item num-

The maintenance codes are entered in the third

b e r sequence.

and fourth positions of the Uniform SMR Code

b. Section III. Special Tools List. N o t a p p l i c a b l e .

format as follows:

(a) T h e m a i n t e n a n c e c o d e e n t e r e d i n t h e

c . Section IV. National Stock Number and Part

t h i r d position will indicate the lowest maintenance

N u m b e r I n d e x . A list, in ascending numerical se-

level authorized to remove, replace, and use the

quence, of all National stock numbers appearing

support item. The maintenance codes entered in

i n the listings, followed by a list, in alphanumeric

the third position will indicate one of the following

sequence, of all part numbers appearing in the list-

l e v e l s of maintenance:

ings. National stock numbers and part numbers

a r e cross-referenced to each illustration figure and

Code

Application/Explanation

D -- S u p p o r t item is removed, replaced, used at the

item

number

appearance.

depot level.

(b) T h e m a i n t e n a n c e c o d e e n t e r e d i n t h e

3. Explanation of Columns

f o u r t h position indicates whether the item is to be

T h e following provides an explanation of columns

repaired

and

identifies

the

lowest

maintenance

f o u n d in the tabular listings:

l e v e l with the capability to perform complete re-

a. Illustration. This column is divided as follows:

pair (i.e., all authorized maintenance functions).

This position will contain one of the following

(1) F i g u r e n u m b e r . Indicates the figure num-

maintenance codes:

b e r of the illustration in which the item is shown.

(2) I t e m n u m b e r . T h e n u m b e r u s e d t o i d e n -

Code

Application/Explanation

t i f y item called out in the illustration.

D--The lowest maintenance level capable of com-

plete repair of the support item is the depot

b. Source, Maintenance, and Recoverability

level.

Codes (SMR).

Z--Nonreparable. No repair is authorized.

(1) Source code. Source codes are assigned to

(3) R e c o v e r a b i l i t y

code. Recoverability

s u p p o r t items to indicate the manner of acquiring

codes are assigned to support items to indicate the

s u p p o r t items for maintenance, repair, or overhaul

d i s p o s i t i o n action on unserviceable items. The re-

of end items. Source codes are entered in the first

c o v e r a b i l i t y code is entered in the fifth position of

and second positions of the Uniform SMR Code

the Uniform SMR Code format as follows.

format as follows: