IDENTIFICATION AND TABULATED DATA.

TM 5-6115-465-12

TO 35C2-3-446-1

NAVFAC P-8-625-12

TM-06858B/06859D-12

f. Mechanical Governing System (Utility Sets

(10) Engine Identification Plate. Located

Only). The mechanical governing system provides

on left side of engine block. Specifies manufac-

the controls and load responses necessary for ef-

turer, manufacturer's specification, model number,

ficient single unit, or parallel, operation of

serial number, date of manufacture, bore, stroke,

utility generator sets. Engine rpm and set fre-

displacement, maximum continuous speed, maximum

quency are controlled by the mechanical governor,

set continuous brake horsepower, lube oil pres-

an integral part of the fuel injection pump,

sure, firing order, intake and exhaust valve tap-

which actuates the fuel metering valve. Adjust-

pet clearances, and military specification.

ment of engine rpm and set frequency is accom-

plished by use of a manual speed control located

(11) Voltage Reconnection Plate. Located on

adjacent to the control cubicle. This control

terminal guard over voltage reconnection board.

is a knob type device which permits rapid fre-

Contains instructions for reconnecting the gener-

quency adjustment, locking in any position, and

ator from 120/208 to 240/416 volts and reconfig-

vernier adjustment for finer control.

uration back to 120/208 volts.

1-6. IDENTIFICATION AND TABULATED DATA.

b. Tabulated Data.

a. Identification. There are eleven major

(1) Engine Generator Set (End Item):

identification and instruction plates on the gen-

Model Numbers:

erator set.

50/60 Hz Tactical Utility . . . . . . . . . . . . MEP-005A

(1) Generator Set Identification Plate.

50/60 Hz Tactical Precise . . . . . . . . . . . . MEP-104A

Located at the top left side of the front housing

400 Hz Tactical Precise . . . . . . . . . . . . . . MEP-114A

assembly. Specifies nomenclature, model number,

serial number, stock number, contract number, en-

DOD Drawing Numbers:

gine serial number, manufacturer, and shipping

weight and dimensions.

MEP-005A . . . . . . . . . . . . . . . . . . . 70-005

MEP-104A . . . . . . . . . . . . . . . . . . . . 70-104

(2) Generator Set Rating Plate. Located at

MEP-114A . . . . . . . . . . . . . . . . . . . . 70-114

top left side of front housing adjacent to gener-

ator set identification plate. Specifies kilowatt

Overall Dimensions and Weights:

capacity relative to altitude and temperature,

hertz rating, rated voltages and phases, voltage

Overall length (MEP-005A,

adjustment ranges, power factor, type, class, mode

MEP-104A, and MEP-114A) . . . . . . . . . . 80 inches

and size.

Overall width (MEP-005A,

(3) Fuel System Diagram Plate. Located on

MEP-104A, and MEP-114A) . . . . . . . . . . 36 inches

inside face of left side generator compartment

access door. Contains diagram of fuel system.

Overall height (MEP-005A,

. . . . 55 inches

MEP-104A, and MEP-114A) . . . . .

(4) Operating Instruction Plate. Located

on inside face of right hand control panel access

Dry Weights (less kits and opt ional equipment):

door. Specifies prestart checks, starting se-

quence, stopping sequence, and instructions for

MEP-005A . . . . . . . . . . . . . . . . . . 2850 pounds

parallel operation.

MEP-104A . . . . . . . . . . . . . . . . . . 2850 pounds

MEP-114A . . . . . . . . . . . . . . . . . 3000 pounds

(5) Schematic and Troubleshooting Diagram

Plates. Troubleshooting plate is located on in-

(2) Engine:

side face of right and left engine compartment

doors. A schematic diagram plate is located on

Manufacturer . . . . . . . . . White Engines, Inc.

the inside of the battery doors of the power gen-

Hercules Engine Div.

eration and control circuits.

Model . . . . . . . . . . . . D-298-ERX37

DOD drawing number . . . . . . 72-2206

(6) Winterization System Diagram and Cau-

Type . . . . . . . . . . . . . . . . . . 6 cylinder, four

tion Plates (furnished with Winterization Kit).

cycle, liquid cooled

Installed on inside face of left rear upper con-

diesel

trol and lower left vent door. Specifies instal-

lation and operation of winterization systems.

Rated horsepower at 1500 RPM . . . . . . 50 continuous

Also includes cautions pertinent to operation of

Rated horsepower at 1800 RPM . . . . . . 57 continuous

winterization kits.

Rated horsepower at 2000 RPM . . . . . . 64 continuous

Al titude degradation,

(7) Lifting and Tie-Down Attachment Informa-

5000 to 8000 ft . . . . . . . . 3% per 1000 feet

tion Plate. Located in the lower right rear

Firing order . . . . . . . . . . . 1,5,3,6,2,4

generator compartment door. Specifies center of

Winterization kit use . . . . When temperature

gravity, tie-down location, lifting shackle lo-

is -25°F or below

cation and capacity and direction of travel.

Valve tappet clearance adjustment:

(8) Battery Reconnection Instruction Plate.

Located inside face of battery compartment access

Hot . . . . . . . . . . . . . 0.015 Inch

door. Contains diagram of battery installation

and specifies cautions to be observed when re-

(3) Cooling System:

placing batteries.

Type . . . . . . . . . . . . . . . . . . . . . Pressurized radia-

(9) Generator Identification Plate. Located

tor and centrifugal

on upper right side of generator housing. Speci-

pump

fies nomenclature, part number, style, rated rpm,

frequency serial number, kva rating, P/F, ampere

Capacity . . . . . . . . . . . . . . . . . 23.5 qts.

rating, voltage, and manufacturer.

1-5

Change 9