How to Locate Repair Parts

three subcolums. Indicated in each subcolumn,

opposite the first appearance of each item, is the

b. Repair parts mortality has been based on

total quantity of items authorized for the number

1,500 hours operation per year.

of equipment supported. Subsequent appearance

c. Parts which require manufacture or assembly

of the same item will have the letters "REF" in

at a category higher than that authorized for in-

the applicable allowance column. To locate the

stallation will indicate in the source column the

referenced item locate the FSN or reference

higher category.

number in the index. The earliest figure and item

number is the referenced item. Items authorized

d. The following publication pertain to the

for use as required but not for initial dockage

generator sets and their components:

are identified with an asterisk in the allowance

Operator's Manual.

TM 5-6115-239-10

column.

Operator, Organiza-

TM 5-6115-247-15

(2) The quantitative allowance for GS/DS

tional, Direct Sup-

levels of maintenance will represent initial stock-

port, General Sup-

age for a 30-day period for the number of equip-

port, and Depot

ments supported.

Maintenance Manual.

(3) To determine allowances when support-

Operator and Organiza-

TM 5-6115-425-12

ing more than 100 of these equipments: First,

tional Maintenance

divide the number of equipments supported by

Manual.

100 by moving the decimal two places left; second,

TM 5-6115-425-25P Organizational, Direct

multiply the result by the quantity in the 51-100

and General Support,

density column. Example, authorized allowance

and Depot Mainte-

for 51-100 equipments is 40; for 150 equipments

nance Repair Parts

multiply 40 by 1.50 or 60 parts required.

and Special Tools

h. One-Year Allowance Per 100 Equipments/

Lists.

Contingency Planning Purposes. Indicates oppo-

Operator, Organiza-

TM 9-2330-205-14

site the first appearance of each item the total

tion, Direct Support,

quantity required for distribution and contin-

and General Support

Maintenance Manual.

gency planning purposes. The range of items-

indicates total quantities of all authorized items

Operator and Organiza-

TM 9-2320-211-12

required to provide for adequate support of 100

tional Maintenance

equipment for one year. Subsequent appearance

Manual.

of the same item will have the letters "REF" in

TM 9-2320-211-20P Organizational Main-

the allowance column.

tenance Repair Parts

and Special Tools

i. Depot Maintenance Allowance Per 100 Equip-

Lists.

ments. Indicates opposite the first appearance of

TM 9-2320-211-35P Direct and General

each item the total quantity authorized for depot

Support, and Depot

maintenance of 100 equipments. Subsequent ap-

Maintenance Repair

pearances of the same item will have letters

Parts, and Special

"REF" in the allowance column. Items authorized

Tools Lists.

for use as required but not for inital stockage

are identified with an asterisk in the allowance

e. The same illustrations are used to illustrate

column.

the repair parts and special tools listed in both

organizational maintenance section and direct

j. Illustration. This column is divided as follows:

support maintenance section.

(1) Figure number. Indicates the figure

number of the illustration in which the item is

shown.

5. How to Locate Repair Parts

a. When Federal stock number or reference

(2) Item number. Indicates the callout num-

number is unknown:

ber used to reference the item in the illustration.

(1) First. Using the the table of contents deter-

mine the assembly group within which the repair

4. Special Information

a. Identification of the usable on codes included

part belongs. This is necessary since illustrations

in the description column of this publication are:

are prepared for assembly groups, and listings

are divided into the same groups.

(2) Second. Find the illustration covering

the assembly group to which the repair part

belongs.