|
| |
- OPERATOR, ORGANIZATIONAL,
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL FOR CONTAINER,
REFRIGERATED MODEL SC209
- WARNING
- WARNING-continued
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- OPERATOR, ORGANIZATIONAL
DIRECT AND GENERAL SUPPORT MAINTENANCE MANUAL is changed as follows
- LIST OF EFFECTIVE PAGES
- TABLE OF CONTENTS
- TABLE OF CONTENTS-contineud
- LIST OF ILLUSTRATIONS
- CHAPTER 1. INTRODUCTION
- Identification and Tabulated
Data.
- Figure 1-1. Refrigerated
Container, Right Front Three-Quarter View.
- Figure 1-2. Refrigerated
Container, Left Rear Three-Quarter View.
- Figure 1-3. Refrigerated
Container, Rear Inside View.
- CHAPTER 2. OPERATING
INSTRUCTIONS
- Section II. MOVEMENT TO A
NEW WORK SITE
- Section III. CONTROL AND
INSTRUMENTS
- Figure 2-1. Rear Doors.
- Figure 2-2. Door Chains.
- Figure 2-3. Spacer Block,
Stowed and Installed.
- Figure 2-4. Temperature
Recorder, Cover Closed.
- Figure 2-5. Temperature
Recorder, Cover Opened.
- Section IV. OPERATION UNDER
USUAL CONDITIONS
- Figure 2-6. Grounding
Connections.
- Operation in Extreme Cold
(Below 0°F)
- Section VI. OPERATION OF
MATERIAL USED WITH THE REFRIGERATED CONTAINER
- CHAPTER 3. OPERATOR'S
MAINTENANCE INSTRUCTIONS
- Table 3-1. Preventive
Maintenance Checks and Services
- Table 3-1. Preventive
Maintenance Checks and Services-continued
- Figure 3-1. Floor Drain and
Hose.
- Section III. TROUBLESHOOTING
- Table 3-2. Troubleshooting
- CHAPTER 4. ORGANIZATIONAL
MAINTENANCE INSTRUCTIONS
- Section III. REPAIR PARTS,
SPECIAL TOOLS AND EQUIPMENT
- Figure 4-1. Rear Doors
Lubrication Points.
- Section V. PREVENTIVE
MAINTENANCE CHECKS AND SERVICES
- Table 4-1. Troubleshooting
- Inspection.
- Figure 4-2. Door Lining
Sheet, Removal and Installation.
- Figure 4-3. Door Gasket,
Repair and Replacement.
- Section VIII. MAINTENANCE OF
DOORS SEALS
- Figure 4-4. Floor Seal,
Removal and Installation.
- Section IX. MAINTENANCE OF
DOOR HARDWARE
- Figure 4-5. Door Hardware,
Identification.
- Figure 4-6. Escape Door and
Document Holder, Removal and Installation.
- Figure 4-7. Manual Holder,
Removal and Installation.
- Section XI. MAINTENANCE OF
FLOOR, FRONT, ROOF, AND SIDES
- Section XII. MAINTENANCE OF
SPACER STRIPS AND CARGO RESTRAINTS
- Section XIV. MAINTENANCE OF
THERMOMETER ELEMENT
- FIGURE 4-8. SPACER STRIPS,
CARGO RESTRAINT, REMOVAL AND INSTALLATION
- FIGURE 4-9. TEMPERATURE
RECORDER, ADJUSTMENT POINTS AND REMOVAL AND INSTALLATION.
- Section XV. MAINTENANCE OF
FUEL SYSTEM
- Figure 4-10. Thermometer
Element, Removal and Installation.
- Figure 4-11. Fuel System
Components, Removal and Installation
- Section XVI. MAINTENANCE OF
POWER CABLE
- Figure 4-12. Power Cable and
Light Wiring Diagram.
- Figure 4-13. Exhaust System
Components and Removal and Installation.
- Removal.
- Section XVIII. MAINTENANCE
OF REFRIGERATION UNIT
- Figure 4-14. Refrigeration
Unit, Removal and Installation.
- Section XIX. MAINTENANCE OF
GENERATOR SET
- Installation-continued
- Figure 4-15. Generator Set
Removal (Sheet 1 of 2).
- Figure 4-15. Generator Set
Removal (Sheet 2 of 2).
- Figure 4-16. Generator Set
Exhaust Removal and Installation.
- Figure 4-17. Generator Set
Installation (Sheet 1 of 4).
- Figure 4-17. Generator Set
Installation (Sheet 2 of 4).
- Figure 4-17. Generator Set
Installation (Sheet 3 of 4).
- Figure 4-17. Generator Set
Installation (Sheet 4 of 4).
- Section XX. MAINTENANCE OF
GENERATOR SLIDE ASSEMBLY
- Figure 4-18. Generator Slide
Assembly Removal and Installation.
- Section XXI. MAINTENANCE OF
IDENTIFICATION PLATE
- Figure 4-19. Identification
Plate Removal and Installation.
- CHAPTER 5. DIRECT AND
GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- Section IV. REMOVAL AND
INSTALLATION OF MAJOR COMPONENTS AND AUXILIARIES
- Figure 5-1. Corner Angle and
Zee, foam Insulation, Removal and Installation.
- Ribbed Flooring.
- CHAPTER 6. REPAIR
INSTRUCTIONS
- Figure 6-1. Rupture Repair
of Panel.
- CHAPTER 7. MAINTENANCE OF
MATERIEL USED IN CONJUNCTION WITH THE REFRIGERATED CONTAINER
- APPENDIX A. REFERENCES
- APPENDIX A.
REFERENCES-continued
- APPENDIX B. COMPONENTS OF
END ITEMS LIST
- Section II. INTEGRAL
COMPONENTS OF END ITEM
- Section III. BASIC ISSUE
ITEMS
- APPENDIX C. ADDITIONAL
AUTHORIZATION LIST
- Section II. ADDITIONAL
AUTHORIZATION LIST
- APPENDIX D. MAINTENANCE
ALLOCATION CHART (MAC)
- Calibrate
- Explanation of Columns in
the MAC, Section II
- Explanation of Columns in
the Tools and Test Equipment Requirements, Section III
- Section II. MAINTENANCE
ALLOCATION CHART FOR CONTAINER, REFRIGERATED MODEL SC209
- Section II. MAINTENANCE
ALLOCATION CHART FOR CONTAINER, REFRIGERATED MODEL SC209-continued
- Section III. TOOLS AND TEST
EQUIPMENT FOR CONTAINER, REFRIGERATED MODEL SC209
- APPENDIX E. EXPENDABLE
SUPPLIES AND MATERIALS LIST
- APPENDIX E. EXPENDABLE
SUPPLIES AND MATERIALS LIST-continued
- ALPHABETICAL INDEX
- ALPHABETICAL INDEX-continued
- ALPHABETICAL INDEX-continued
- ALPHABETICAL INDEX-continued
- ALPHABETICAL INDEX-continued
- Instructions for sending an
electronic 2028
- The Metric System and
Equivalents
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- TM-55-8115-202-14
- Blank Page
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Distribution
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- Blank Page
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- RECOMMENDED CHANGES TO
PUBLICATIONS AND BLANK FORMS
- Blank Page
- Blank Page
- Blank Page
- DISTRIBUTION
- Blank Page
|
|
Click
here for thousands of PDF manuals