TM 5-3805-254-20P F - Direct  support  or  aviation  intermediate  is  the  lowest level than can do complete repair of the item. H - General   support   is   the   lowest   level   that   can   do complete repair of the item. L - Specialized repair activity is the lowest level that can do complete repair of the item. D - Depot is the lowest level that can do complete repair of the item. Z - Nonreparable.  No repair is authorized. B - No repair is authorized.  (No parts or special tools are authorized for the maintenance of a "B"-coded item.) However, the item may be reconditioned by adjusting, lubricating, etc., at the user level. (3) Recoverability Code. Recoverability codes are assigned to items to indicate the disposition  action on unserviceable items.  The recoverability code is entered in the fifth position of the SMR code as follows: Code Application/Explanation Z - Nonreparable  item.    When  unserviceable,  condemn and  dispose  of  the  item  at  the  level  of  maintenance shown in the 3d position of the SMR code. O - Reparable   item.      When   uneconomically   reparable, condemn and dispose of the item at unit maintenance or aviation unit level. F - Reparable    item.    When  uneconomically  reparable, condemn    and    dispose    of    the    item    at    the    direct support or aviation intermediate level. H - Reparable    item.    When  uneconomically  reparable, condemn   and   dispose   of   the   item   at   the   general support level. D - Reparable   item.      When   beyond   lower   level   repair capability, return to depot. Condemnation and disposal of item not authorized below depot level. L - Reparable item.  Condemnation and disposal of item not     authorized     below     specialized     repair     activity (SRA). A - Item    requires    special    handling    or    condemnation procedures because of specific reasons (e.g., precious   metal   content,   high   dollar   value,   critical material, or hazardous material).  Refer to appropriate manuals/directives for specific instructions. c. CAGEC   (Column   (3)).      The   Commercial   and Government Entity (CAGE) Code (C) is a 5-digit alphanumeric code which is used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. d. PART   NUMBER   (Column   (4)).      Indicates   the primary number used by the manufacturer (individual, company,   firm,   corporation,   or   Government   activity),   which controls the design and characteristics of the item by means of its engineering drawings, specifications standards, and inspection requirements to identify an item or range of items. NOTE: When you use an NSN to requisition an item, the item you  receive  may  have  a  different  part  number  from  the  part ordered. e. DESCRIPTION AND USABLE ON CODE (UOC)   (Column   (5)).      This   column   includes   the   following information: (1) The Federal item name and, when required, a minimum description to identify the item. (2) Physical security classification. Not Applicable. (3) Items that are included in kits and sets are listed below the name of the kit or set on Figure KIT. (4) Spare/repair     parts     that     make     up     an assembled item are listed immediately following the assembled item line entry. (5) Part     numbers     for     bulk     materials     are referenced in this column in the line item entry for the item to be manufactured/fabricated. (6) When  the  item  is  not  used  with  all  serial numbers of the same model, the  effective  serial  numbers  are shown on the last line(s) of the description (before UOC). (7) The usable on code, when applicable (see paragraph 5, Special Information). (8) In the Special Tools List section, the basis of issue (BOI) appears as the last line(s) in the entry for each special    tool,     special     TMDE,     and     other     special     support equipment.    When  density  of  equipments  supported  exceeds density   spread   indicated   in   the   basis   of   issue,   the   total authorization is increased proportionately. (9) The statement "END OF FIGURE" appears just below the last item description in Column 5 for a given figure in both Section 11 and Section III. f. QTY (Column (6)).  The QTY (quantity per figure column) indicates the quantity of the item used in the breakout shown    on    the    illustration/figure,    which    is    prepared    for    a functional group, subfunctional group, or  an  assembly.    A  "V" appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from application to application. 3