|
| |
Back
TABLE OF CONTENTS | Up
TM-5-2410-234-34P Tractor Full Tracked. Low Speed Heavy Drawbar Pull (Size T-11) W/Angle Dozer Winch and Rops Manual | Next
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LISTS (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST) |
viii
TM 5-2410-234-34P
TABLE OF CONTENTS
ILLUS
PAGE
FIG
PILOT VALVE FOR RIPPER
205-1
205
SELECTOR VALVE (TYPE 1 AND 2)
206-1
206
RIPPER ANDTILT CYLINDER VALVE
207-1
207
ADJUSTABLE RIPPER AND TILT BLADE CYLINDER VALVE
208-1
208
RIPPER VALVE
209-1
209
ADJUSTABLE RIPPER VALVE
210-1
210
RIPPER CONTROL VALVE
211-1
211
ADJUSTABLE RIPPER CONTROL VALVE
212-1
212
HYDRAULIC CONTROL VALVE HARDWARE
213-1
213
HYDRAULIC CONTROL VALVE SPRINGS, SEALS AND PLUGS
214-1
214
HYDRAULIC CONTROL VALVE SUBORDINATE VALVES
215-1
215
BLADE TILT CYLINDER VALVE
216-1
216
BLADE TILT CYLINDER PILOT VALVE
217-1
217
PRESSURE CONTROL VALVE
218-1
218
HYDRAULIC TANK ATTACHING PARTS
219-1
219
2403- HYDRAULIC CONTROLS AND MANUAL CONTROLS
220-1
IMPLEMENT LINKAGE USE (USE ON 8A BULLDOZERS)
220-1
220
IMPLEMENT LINKAGE USE (USE ON 8S BULLDOZERS)
221-1
221
IMPLEMENT LINKAGE USE (USE WITH RIPPER)
222-1
222
LEVER HOUSING
223-1
223
2404- TILT CYLINDERS AND TILT CRANK
224-1
TILT CYLINDERS AND TILT CRANK
224-1
224
2406- STRAINERS, FILTERS, LINES AND FITTINGS ETC
225-1
PUMP LINES, TYPE 2 (USE ON 8A BULLDOZER WITH
SINGLE VALVE)
225-1
225
PUMP LINES, TYPE 3 (USE ON 8A BULLDOZER WITH
SINGLE VALVE)
226-1
226
PUMP HOSES, TYPE 1, 2 AND 3 (USE WITH
DOUBLE VALVE)
227-1
227
PUMP LINES, TYPE 1 AND 3 2 (USE WITH DOUBLE
VALVE)
228-1
228
PUMP LIN ES, TYPE 2 (USE WITH DOUBLE VALVE)
229-1
229
RIPPER PIN PULLER LINES, TYPE 1, 2 AND3
230-1
230
PIN PULLER LINES
231-1
231
RIPPER LINES, LEFT AND RIGHT
232-1
232
BULLDOZER LINES
233-1
233
BULLDOZER LINES AND FITTINGS
234-1
234
TILT CYLINDER HYDRAULIC LINES
235-1
235
TILT CYLINDER LINES
236-1
236
HYDRAULIC FILTER
237-1
237
2407- HYDRAULIC CYLINDERS
238-1
LIFT CYLINDERS MOUNTING HARDWARE, LEFT HAND
238-1
238
LIFT CYLINDERS MOUNTING HARDWARE, RIGHT HAND
239-1
239
RIPPER CYLINDER, LEFT AND RIGHT
240-1
240
RIPPER CYLINDER, CENTER
241-1
241
HYDRAULIC RIPPER CYLINDER
242-1
242
2408- LIQUID TANKS OR RESERVOIRS
243-1
HYDRAULIC TANK ASSEMBLY
243-1
243
HYDRAULIC TANK COVER AND PLATES
244-1
244
HYDRAULIC TANK CAP PROTECTION COVER
245-1
245
GROUP 47
GAGES, WEIGHING AND MEASURING DEVICES
4702-GAGES, MOUNTINGS, LINES AND FITTINMGS
246-1
PRESSURE GAGES
246-1
246
SERVICE METER, 4N4445 ENGINE
247-1
247
PRESSURE GAGES LINES AND FITTINGS
248-1
248
GROUP 60
STEAM BOILERS, WATER HEATERS, HEATING UNITS BURNERS
6015- WATER HEATER ASSEMBLY
249-1
WATER HEATER JACKET
249-1
249
PILOT VALVE FOR RIPPER
205-1
205
SELECTOR VALVE (TYPE 1 AND 2)
206-1
206
|
