SECTION I INTRODUCTION

SECTION I

INTRODUCTION

Explanation

Code

1-1. Scope

wise would be coded PA except that it is

This manual lists repair parts and special tools re-

deteriorative in nature.

quired for the performance of organizational, direct

PD - Support item, excluding support equipment,

support, general support, and depot maintenance of

procured for initial issue or outfitting and

the TS-909/PPM. The PCCN for the TS-909/PPM is

stocked only for subsequent or additional

GRRAAO for all models.

initial issues or outfitting. Not subject

to automatic replenishment.

1-2. General

PE - Support equipment procured and stocked for

This repair parts and special tools list is divided into

initial issue or outfitting to specified main-

the following sections:

tenance repair activities.

a. Prescribed Load Allowance (PLA)-Section II.

PF - Support equipment which will not be stocked

Not applicable.

but which will be centrally procured on de-

b. Repair Parts List-Section III. A list of repair

mand.

parts authorized for the performance of maintenance

PG - Item procured and stocked to provide for sus-

at the organizational level. This repair parts list is

tained support for the life of the equipment.

arranged in alphabetical order.

It is applied to an item peculiar to the equip-

c. Special Tools, Test and Support Equipment-

ment which because of probable discon-

Section IV. Not applicable.

tinuance or shutdown of production facili-

d. Repair Parts List-Section V. A list of repair

ties would prove uneconomical to reproduce

parts authorized for the performance of maintenance

at a later time.

at the direct support, general support, and depot

KD - An item of depot overhaul/repair kit and not

level.

purchased separately. Depot kit defined as

e. Special Tools, Test and Support Equipment-

a kit that provides items required at the

Section VI. Not applicable.

time of overhaul or repair.

f. Index-Federal Stock Number and Reference

KF - An item of a maintenance kit and not pur-

Number Cross-Reference to Figure and Item Num-

chased separately. Maintenance kit defined

ber-Section VII. A list, in ascending numerical se-

as a kit that provides an item that can be re-

quence, of all Federal stock numbers appearing in

placed at organizational or direct support

the listings, followed by a list, in alphameric se-

or general support levels of maintenance.

quence, of all reference numbers appearing in the

KB - Item included in both a depot overhaul/repair

listings. Federal stock number and reference num-

kit and a maintenance kit.

bers are cross-referenced to each illustration figure

MO - Item to be manufactured or fabricated at or-

and item number or reference designation appear-

ganizational level.

ance.

MF - Item to be manufactured or fabricated at di-

rect support maintenance level

1-3. Explanation of Columns

MH - Item to be manufactured or fabricated at gen-

The following provides an explanation of columns

eral support maintenance level.

found in the tabular list.

MD - Item to be manufactured or fabricated at de-

a. Source, Maintenance, and Recoverability Codes

pot maintenance level.

(SMR).

AO - Item to be assembled at organizational level.

(1) Source code. Indicates the manner of acquir-

AF - Item to be assembled at direct support main-

ing support items for maintenance, repair, or over-

tenance level.

haul of end items. Source codes are-

AH - Item to be assembled at general support main-

Explanation

Code

tenance level.

PA - Item procured and stocked for anticipated or

AD - Item to be assembled at depot maintenance

known usage.

level.

XA - Item is not procured or stocked because the

PB - Item procured and stocked for insurance pur-

poses because essentiality dictates that a

requirements for the item will result in the

minimum quantity be available in the sup-

replacement of the next higher assembly.

ply systems.

XB - Item is not procured or stocked. If not avail-

PC - Item procured and stocked and which other-

able through salvage, requisition.