Special Information

TM 11-5815-246-34P

Explanation

Code

e. Quantity Incorporated in Unit. This column

i n d i c a t e s the quantity of the item, used in the

F Repairable item, When uneco-

e q u i p m e n t , Subsequent appearance of the same

nomically repairable, condemn

item in the same assembly are indicated by the

a n d dispose at the direct support

l e t t e r s "REF",

level.

f. 30-Day DS/GS Maintenance Allowances.

H Repairable item. When uneco-

nomically repairable, condemn

NOTE

and dispose at the general support

Allowances in GS column are for GS

level,

m a i n t e n a n c e only.

D Repairable item. When beyond lower

l e v e l repair capability, return to

( 1 ) The repair parts indicated by asterisk

depot. Condemnation and disposal

entries in separate allowance columns for DS and

not authorized below depot level.

G S represent those authorized for use at that

L Repairable item. Repair, con-

category of maintenance to be requisitioned on an

demnation, and disposal not

" a s required" basis, until stockage is based on

authorized

below

depot/

demand in accordance with AR 710-2.

S p e c i a l i z e d Repair Activity level.

(2) Allowance quantities are indicated in the

A Item requires special handling or

special tool lists section for special tools, TM DE,

c o n d e m n a t i o n procedures because

a n d other support equipment.

of specific reasons (i. e., precious

g. 1-Year Allowances P e r 1 0 0 E q u i p -

m e t a l content, high dollar value,

m e n t s / C o n t i n g e n c y Planning Purposes. C o l u m n

or hazardous

material

critical

i n t e n t i o n a l l y left blank.

material).

h. Depot Maintenance Allowance Per 100

b. Federal Stock Number. Indicates the

E q u i p m e n t s . This column indicates opposite the

F e d e r a l stock number assigned to the item.

first appearance of each item the total quantity

authorized for depot maintenance of 100 equip-

NOTE

ments.

For requisitioning purposes, the Federal

i . Illustration. T h i s c o l u m n i s d i v i d e d a s

stock number must be converted to the

follows:

National stock number by adding

(1) F i g u r e n u m b e r . I n d i c a t e s t h e f i g u r e

"-00-" after the Federal stock

number of the illustration on which the item is

c l a s s i f i c a t i o n (FSC) code (first four

shown in TM 112258.

FSN

For

example,

digits).

(2) Item number. Indicates the item number

6625-553-0142 converts to NSN

or reference designation used to reference the item

6625-00-553-0142.

i n the illustration.

c. Description. I n d i c a t e s t h e F e d e r a l i t e m

1-4. Special Information

n a m e and a minimum description required to

a. Usable on codes are included in column 3.

identify the item. T h e last line indicates the

U n c o d e d items are applicable to all models.

reference number followed by the applicable

Identification of the usable on codes used in this

Federal Supply Code for Manufacturer (FSCM) in

p u b l i c a t i o n are

parentheses. The FSCM is used as an element in

Used on

Code

i t e m identification to designate manufacturer or

d i s t r i b u t o r or Government agency, etc., and is

BXI

AN/TX C-1

identified in SB 70842.

BXJ

AN/TXC-1A

d. Unit of Measure (U/M). Indicates

the

BXK

AN/TXC-1B

s t a n d a r d or basic quantity by which the listed

BXL

AN/TXC-1C

item is used in performing the actual maintenance

BXM

AN/TXC-1D

f u n c t i o n . This measure is expressed by a two-

c h a r a c t e r alphabetical abbreviation; e.g., ea, in,

b. The following publications pertain to the

pr, etc., and is the basis used to indicate quan-

e q u i p m e n t and its components:

t i t i e s and allowances in subsequent columns.

When the unit of measure differs from the unit of

TM 11-2258

Facsimile Sets AN/TXC

-1, -1A, -lB, -lC, and

issue, the lowest unit of issue that will satisfy the

-1D.

required units of measure will be requisitioned.