'TM 11-5815-246-20P' by LOGSA

c. Description. Indicates the Federal item name

Code

Used on

and a minimum description required to identify the item.

RVT

AN/TXC-1

The last line indicates the reference number followed by

BXJ

AN/TXC-1A

the applicable Federal Supply Code for Manufacturer

BXK

AN/TXC-1B

(FSCM) in parentheses. The FSCM is used as an

BXL

AN/TXC-1C

element in item identification to designate manufacturer

BXM

AN/TXC-1D

or distributor or Government agency, etc., and is

identified in SB 708-42.

b. The following publication pertains to the

d. Unit of Measure (U/M). Indicates the standard

equipment and its components:

or basic quantity by which the listed item is used in

TM 11-2258

Facsimile Sets AN/TXC-1, -1A,

performing the actual maintenance function.

This

-1B, -1C, and -1D.

measure is expressed by a two-character alphabetical

abbreviation; e.g., ea, in, pr, etc., and is the basis used

1-5. Location of Repair Parts

to indicate quantities and allowances in subsequent

a. This manual contains one cross-reference index

columns. When the unit of measure differs from the unit

(sec V) to be used to locate a repair part when either the

of issue, the lowest unit of issue that will satisfy the

Federal

stock

number

reference

number

required units of measure will be requisitioned.

(manufacturer's part number) is known. The first column

e. Quantity Incorporated in Unit.

This column

in the index is prepared in numerical or alphanumeric

indicates the quantity of the item used in the equipment.

sequence in ascending order. The reference numbers

Subsequent appearances of the same item in the same

(manufacturer's part numbers) are listed immediately

assembly are indicated by the letters "REF".

following the last listed Federal stock number in the

f. 15-Day Organizational Maintenance Allowance.

index of Federal stock numbers.

(1) The repair parts indicated by an asterisk in

b. When the Federal stock number or reference

the allowance column represent those authorized for use

number is known, follow the procedures given in (1) and

at the organizational category, and will be requisitioned

(2) below.

on an "as required" basis, until stockage is based on

(1) Refer to the index of Federal stock numbers

demand in accordance with AR 710-2.

(sec V) and locate the Federal stock number or

(2) Major Army commanders are authorized to

reference number. The FSN and reference number are

approve reduction in the range of support items

cross-referenced to the applicable figure and item

authorized for use in units within their commands.

number or reference designation.

Recommendations for increase in range of items

(2) Refer to the repair parts list (sec III) and

authorized for use will be forwarded to Commander, US

locate the figure number (col 7a) and item number or

Army Electronics Command, ATTN: AMSEL-MA-CW,

reference designation (col 7b) as noted in the FSN

Fort Monmouth, N.J., 07703. Any changes approved will

index.

be reflected in a revision to the RPSTL.

c. When the figure and item number or reference

(3) Allowance quantities are indicated in the

designation are known, scrutinize columns 7a and 7b of

special tools list section for special tools, TMDE, and

the repair parts list (sec III) until the item is located.

other equipment.

d. When the FSN, reference number, figure

g. Illustration. This column is divided as follows:

number, item number and reference designation are not

(1) Figure number. Indicates the figure number

known, scrutinize column 3 of the repair parts list (sec

of the illustration on which the item is shown in

III), which is arranged in alphabetical order.

TM 11-2258.

(2) Item number. Indicates the item number or

1-6. Abbreviations

reference designation used to reference the item in the

Not applicable.

illustration.

1-7.

Reporting

Equipment

Publication

1-4. Special Information

Improvements

a. Usable on codes are included in column 3.

The

reporting

errors,

omissions,

and

Uncoded items are applicable to all models.

recommendations for improving this publication by the

Identification of the usable on codes used in this

individual user is encouraged.

Reports should be

publication are -

submitted on DA Form 2028 (Recommended Changes

to Publications and Blank Forms) and forwarded direct to

Commander, US Army Electronics Command, ATTN:

AMSEL-MA-CW, Fort Monmouth, NJ 07703.

(Next printed page is 6)