Installation Instructions

TM 5-6350-262-14/6

NAVELEX 0967-LP-466-9062

TO 31S9-4-33-1

Table 2-1. Installation Tools and Test Equipment

Applicable

Items

Purpose

publication

Power Supply (Requirements:

Pre-installation checkout

(Not available)

Voltage: 1-40 V dc, 0-0.5 amp

Current: 25 to 50 ma.)

VOM, TS352B, 6625-533-0142

Pre-installation checkout

(Not available)

Tool Kit, TK105G 5180-10-8177

Contains hand tools commonly used in electronic repair shops

(Not available)

AC Power Plug - 3 leads

Pre-installation checkout

(Not available)

Resistor, 10KO, 1%

Pre-installation checkout

(Not available)

2-6.

Installation Instructions

(12) Slide the inner enclosure into position in

the outer enclosure ensuring that the slides are properly

a. Figure 2-1 shows pertinent equipment external

mated.

dimensions, mounting hole spacing and interconnecting

(13) Remove two screws (22, fig. C-1) and

wiring access for installation planning purposes.

barrier cover (23).

b. Perform the following procedure to install the

(14) Place POWER switch in the OFF position.

audible alarm.

WARNING

(1) Prior to installation, check equipment

Power to the J-SIID system must be

performance in accordance with table 5-1.

shut- down before any leads are

(2) Using the key, unlock and open the outer

connected to the audible alarm.

enclosure door.

(3) Remove the inner housing cover by

(15) Connect the JSIIDS interfacing wires from

loosening the pan head screws (2, fig. C-1) at each

the Control Unit to the appropriate terminals on terminal

corner of the cover.

group L1 and L2 as follows (see fig. 5-2 for terminal

(4) Disconnect the tamper switches (S1 and

group location).

S2), by separating connector P2 (6).

WARNING

(5) Remove the inner enclosure from the

A 115-volt potential may cause death

outer enclosure by sliding out.

under certain conditions; therefore,

(6) Remove the external tamper switch plug

reasonable precautions should be taken

provision (see fig.

2-2) in accordance with the

at all times.

instructions on the back side of outer housing.

CAUTION

Terminal Group L1

Terminal Grp L2

Function

1 ....................................... AC Power

Conduit must not extend more than

2 ....................................... AC Power

one-half (1/2) inch inside outer

3 ....................................... Ground to Housing

enclosure to prevent a grounding

1 ................. Alarm Input

potential which could cause damage to

2 ................. Signal Common

the equipment.

3 ................. LAA Tamper Output

(7) Insert the J-SIID system interfacing wiring

4 ................. Spare

electrical conduit in the appropriate entry hole provided

5 ................. Spare

on the back panel of the out) enclosure shown in figure

(16) Connect plug P2 (6, fig.

C-1) to

2-2.

connector J2 (36).

(8) Using 1/4 inch bolts, mount the outer

(17) Replace terminal group L1 barrier cover

enclosure (see fig. 2-1) to the selected mounting

(23).

surface.

(18) Remove one screw and washer (17 and

(9) Pull the conduit wiring through the

18) and the battery clamp bracket (19).

conduit, leaving approximately one (1) foot of wire

WARNING

length extending into the enclosure.

Do not install battery without first

(10) Make a visual inspection of interfacing

recharging and testing in accordance

wires to insure there are no frayed, nicked or bare wires.

with instructions given in chapter 5. To

(11) Position the inner enclosure so that the

do so may create a safety hazard.

wire leads can be routed through the access port

(19) Install battery with positive terminal at top

provided on the rear panel of the inner enclosure shown

of inner enclosure.

in figure 22.

Change 2 2-2