TM-9-2815-252-240001.gif
TM-9-2815-252-240002.gif
TM-9-2815-252-240003.gif
TM-9-2815-252-240004.gif
TM-9-2815-252-240005.gif

Tm-9-2815-253-24

• Chapter 1 Introduction
• Section Ii. Equipment Description And Data
• Figure 1-1. Engine Components
• Section Iii. Preparation For Use
• Chapter 2 Operation
• Chapter 3 Maintenance
• Table 3-2. Troubleshooting
• 4. Engine Hard To Start Or Will Not Start In Cold Weather
• 6. Engine Does Not Develop Full Power.
• 8. Excessive Oil Consumption.
• 11. Black Or Gray Smoke.
• 13. Abnormal Engine Noise
• Section Iii. General Maintenance
• 3-4. Disassembly And Assembly Sequence For Overhaul
• 3-4.2. Assembly
• 3-5. Crankcase Vacuum
• Figure 3-1. Locally Manufactured Water Manometer
• Section Iv. Intake And Exhaust System Maintenance
• Figure 3-3. Exhaust Manifold
• Section V. Cooling System Maintenance
• Figure 3-4. Cooling System
• 3-10.2. Inspection.
• Section Vi. Fuel System Maintenance
• 3-13. Fuel Injection Pump
• Figure 3-7. Fuel Injection Pump, Fuel Filter, And Supply Lines
• 3-13.3. Test.
• Figure 3-9. Setting Pump Rack
• 3-14. Fuel Injection Pump Timing.
• Figure 3-10. Checking Piston Drop
• 3-15. Fuel Supply Lines.
• Figure 3-12. Fuel Filter
• 3-17. Fuel Injector
• Figure 3-13. Fuel Injector, Fuel Injector Pipes, And Fuel Return Line
• 3-18. Fuel Injector Pipes And Fuel Return Line
• 3-19. Fuel Solenoid.
• Figure 3-14. Fuel Solenoid Installation
• Section Vii. Lubrication System Maintenance
• Figure 3-15. Oil Filter And Crankcase Door
• Figure 3-16. Crankcase Door Fastener Tightening Sequence
• Figure 3-17. Strainer And Oil Pump
• Section Viii. Governor System Maintenance
• Figure 3-19. Governor System
• 3-23.2. Repair.
• Figure 3-20. Governor Weights
• 3-23.5. Adjustment
• Section Ix. Electrical System Maintenance
• Figure 3-21. Starter Connection And Mounting Hardware
• Figure 3-23. Starter Solenoid Test Circuit
• Figure 3-24. Solenoid Terminals
• Figure 3-25. Overrunning Clutch
• Figure 3-26. Checking Pinion Gap
• Section X. Engine Subassembly Maintenance
• Figure 3-27. Cylinder Cover And Rocker Lever
• 3-27. Cylinder Head Assembly
• Figure 3-28. Cylinder Head Assembly
• 3-27.2. Disassembly
• Table 3-4. Cylinder Head Component Wear Limits
• Figure 3-29. Valve Guide Tool And Depth Stop
• 3-27.5. Assembly.
• Figure 3-31. Cylinder Head Bolt Tightening Sequence
• 3-28. Gear End Cover.
• Figure 3-32. Gear End Cover
• Figure 3-33. Gear End Cover Capscrew Tightening Sequence
• Table 3-5. Camshaft Component Wear Limits
• Figure 3-35. Measuring Gear Backlash
• Figure 3-36. Piston And Connecting Rod Assemblies
• 3-30.2. Inspect And Measure
• Table 3-6. Piston And Connecting Rod Component Wear Limits
• Figure 3-37. Piston Ring And Gap Location
• 3-31. Flywheel Housing
• Figure 3-39. Center Bearing Tube
• Figure 3-40. Crankshaft Assembly
• Figure 3-41. Main Bearing Tool
• Figure 3-42. Bearing Housing Capscrew Tightening Sequence
• 3-33.2. Inspect And Measure
• Table 3-7. Crankshaft Component Wear Limits
• 3-34. Crankcase Assembly
• Figure 3-43. Crankcase Assembly
• G. Using Main Bearing Tool
• 3-34.3. Inspection.
• Appendix A References
• Appendix B Maintenance Allocation Chart
• B-3. Explanation Of Columns In The Mac
• Section Ii. Maintenance Allocation Chart For Diesel Engine Model Dn4m
• Maintenance Allocation Chart For Diesel Engine Model Dn4m -Cont
• Maintenance Allocation Chart For Diesel Engine Model Dn4m -Cont
• Maintenance Allocation Chart For Diesel Engine Model Dn4m -Cont
• Appendix C Expendable/Durable Supplies And Materials List
• Appendix D. Maintenance Procedure And Authorized Level Of Maintenance
• Section Iii. Maintenance Level To Paragraphs
• Appendix E Torque Chart
• Index
• Index - Continued
• Index - Continued
• Index - Continued
• Index - Continued
• Index - Continued
• The Metric System And Equivalents

Privacy Statement - Press Release - Copyright Information. - Contact Us